• New

Pole mount LiFeP04 Solar System for 12V IP Cameras - 80W

Tax included

A off grid Pole mount Solar System for 12V IP Cameras. This pole-mounted solar power kit with Lithium battery is the perfect solution to your remote power needs for deploying a camera.  This unit has a larger 80W solar panel for quicker recovery and charging plus either a 20Ah or 25Ah LiFeP04 12V battery pack.

Read our FAQ on Solar here

Read our article on what size is best for you here

Solar Battery pack LiFeP04 size
Last items in stock

  Delivery policy

All local packages are shipped via The Courier Guy with tracking and drop-off with signature.

Are you looking for a way to provide power and remote connectivity to your own IP camera or other device in an off-grid area? Then Foscam CCTV has the solution.

Foscam’s Off Grid Solar Security Hub provides a regulated 12v supply to power your device along with a standard USB outlet. This model is equipped with an oversized 80W panel to enable faster recharge time for those cloudy days and help reduce down time.

The system has its own Lithium battery charged via an on-board solar panel allowing it to run indefinitely without recharging from the mains. It’s completely silent – perfect for residential areas or a long deployment. The power system is designed for SA conditions and is fully compliant with SA electrical regulations. It includes an industrial 12v regulated power supply to protect your equipment from voltage variances.

System parameters:-  1 x 12V 20Ah LiFeP04 or 25Ah LiFeP04 depending on your selection.


Pole mount housing

The entire system is housed in an industrial grade IP66 rated enclosure supported by a rugged pole mount frame. The standard enclosure is designed to connect to an external device (such as an IP camera and LTE router).

Pole mount for solar panel: Aluminum alloy brackets with stainless steel hardware

Setting angle: 45° for capturing the correct angle for the sun

Mounting pole (to be supplied by installer/customer for combination of solar panels and battery/control box): recommended minimum - 75-100mm x 3mm steel for 3metre above ground.

NOTE: POLE is NOT INCLUDED in the kit and dimension are only a guideline. It is the responsibility of the client to ensure that correct erection procedure for the pole is followed.

Wind load: 80Kkm/Hr

Hail loading: 1.1Kn/m ²

Assembled weight (includes 1 x 80W panel): 11.2kg without the camera

Attention: Edges may be sharp

Solar panel mount set comes with: 1 upper bracket, 1 lower bracket, 2 x U-bolts (straps), 2 x M6 hex-head bolts, 4 x washers, 2 x M6 nyloc nuts, 2 x M6 hex-head bolts for solar panel, 4 x flat washers for solar panel, 2 x nyloc nuts for solar panel.

Installation: To the greatest extent possible, the installation site should allow unshaded exposure to the sun throughout daylight hours.

SPECIFICATIONS – Control and Battery Cabinet

STANDARD 12VDC 20Ah 80W Solar

Enclosure complete with:

20Ah LiFeP04 battery pack + BMS

SRE Solar Charge Controller

Dedicated 12VDC Voltage protector for camera

Unregulated (charging voltage) DC supply for CPE / gateway

Power Connector (5 x 2.2mm), glands, Solar Panel integrated mounting brackets

80W Solar panel

Integrated pole mount brackets - Unistrut 75mm to 100mm

Depending upon the customer requirement, two battery pack options are available in the enclosure shown being 20Ah or 25Ah.

Solar charging is by means of a Monocrystalline Solar panel.

The solid state controller integrates all aspects required for optimal operation of the unit with:

  • Solar charge controller specifically for LiFepo4 cells with BMS.
  • Regulated 2 X 12V outputs and a USB 5V

Cabinet: Polyester / Polycarb

Pole mount bracket: Unistrut  strap top and bottom

Batteries: 1 x 12V 20Ah LiFeP04 or 25Ah LiFeP04 batt pack

Solar Charge Controller: 10A

Camera Voltage Protector: 2A

Connectivity (not supplied in this base kit but we can supply on request)

An 4G GSM modem runs on any mobile network allowing you to connect to the system from virtually anywhere – as long as the system is in an area with good network coverage. Speeds of are location dependent.

(Sim Card– supplied by customer depending on your service provider)

Depending on your requirements you can use any router as long as it can be power by 12V. 

We recommend something like the Mikrotik LtAP Mini LTE Router.


We custom build to suit your project or device, let us know what you are looking for by email or call us on +27 11 465 9173 and we’ll provide you with a quote.

1 Items

Specific References

in the same category