Tax included
Reference: FOS-SOL-K24AH

A off grid Pole mount Solar System for Foscam IP Cameras. These pole-mounted solar power kits with Lithium battery are the perfect solution to your remote power needs for deploying a remote camera.  2 x 12V 12Ah LiFeP04, 60hr to 00hr run-time (Winter solstice)

Stated runtime is based on one Foscam camera and supplied LTE router or TP-Link CPE only

Read our FAQ on Solar here.

Please note this kit does NOT include a camera

By Order Only - Lead time 14 days


Are you looking for a way to provide power and remote connectivity to your own IP camera or other device in an off grid area? Then Foscam CCTV has the solution.

Enclosure complete with:

24Ah LiFeP04 battery pack + BMS

Solar Charge Controller

Dedicated 12VDC Voltage protector for 2 x Cameras

Dedicated 5VDC USB connector

Unregulated (charging voltage) DC supply for CPE / gateway

Power Connectors (5 x 2.2mm), glands, Solar Panel integrated mounting brackets


60W (2 x 30W) Solar panel complete with:

Integrated pole mount brackets, U-clamps for 50mm diameter pole

Foscam’s Off Grid Solar Security Hub provides a regulated 12v supply to power your device along with a standard USB outlet. This model will power one Foscam camera 24/7 with back-up battery with 60hr to 80hr run-time (Winter solstice).

Power system

The system has its own Lithium battery charged via an on board solar panel allowing it to run indefinitely with out refuelling or recharging from the mains. It’s completely silent with no noisy generators or hazardous fuel stored on site – perfect for residential areas or a long deployment. The power system is designed for SA conditions and is fully compliant with SA electrical regulations. It includes an industrial 12v regulated power supply to protect your equipment from voltage variances.

System parameters :-  2 x 12V 12Ah LiFeP04,  30hr to 40hr run-time (Winter solstice)

Recovery time from full discharge: less than 30mins at 50% solar power.


Pole mount housing

The entire system is housed in an industrial grade IP66 rated enclosure supported by a rugged pole mount frame. The standard enclosure is designed to connect to an external device (such as an IP camera).

Pole mount for solar panel: Aluminium alloy brackets with stainless steel hardware

Setting angle: 45° for capturing the correct angle for the sun

Mounting pole (to be supplied by installer/customer for combination of solar panels and battery/control box): recommended minimum - 75mm x 3mm steel for 3metre above ground

NOTE: POLE is NOT INCLUDED in the kit and dimension are only a guideline. It is the responsibility of the client to ensure that correct erection procedure for the pole is followed.

Wind load: 80Kkm/Hr

Hail loading: 1.1Kn/m ²

Assembled weight (includes 2 x 30W panel): 5kg

Attention: Edges may be sharp

Solar panel mount set comes with: 1 upper bracket, 1 lower bracket, 2 x U-bolts (straps), 2 x M6 hex-head bolts, 4 x washers, 2 x M6 nyloc nuts, 2 x M6 hex-head bolts for solar panel, 4 x flat washers for solar panel, 2 x nyloc nuts for solar panel.

Installation: To the greatest extent possible, the installation site should allow unshaded exposure to the sun throughout daylight hours.

SPECIFICATIONS – Control and Battery Cabinet

Depending upon the customer requirement, two battery pack options are available in the enclosure shown being6Ah or 12Ah.

Solar charging is by means of a Monocrystalline Solar panel

The solid state controller integrates all aspects required for optimal operation of the unit with:

  • Solar charge controller specifically for LiFepo4 cells with BMS on 12Ah unit
  • Regulated outputs for two cameras and a USB communication device
  • Raw output for a 12V - CPE link

Cabinet: Polyester / Polycarb 300 x 250 x 130mm

Pole mount bracket: U-clamp / strap top and bottom

Batteries: 2 x 12V 6Ah LiFeP04 batt pack

Solar Charge Controller: 10A

Camera Voltage Protector: 2A


An 4G GSM modem runs on any mobile network allowing you to connect to the system from virtually anywhere – as long as the system is in an area with good network coverage. Speeds of are location dependent.

(Sim Card– supplied by customer depending on your service provider)

Depending on your requirments you can use any router as long as it can be power by 12V. 

We recommend something like the Mikrotik LtAP Mini LTE Router.



Power Connectors for: Camera; Router; Solar panels

Total Weight of control and battery cabinet: 8kg

Cabinet mounting set comes with:

1 upper bracket, 1 lower bracket, 2 x U-bolts (straps),

4 x M6 hex-head bolts, 8 x washers, 4 x M6 nyloc nuts

We custom build to suit your project or device, let us know what you are looking for by email or call us on +27 11 465 9173 and we’ll provide you with a quote.


Specific References


in the same category