• New

FOS-SOL-K24ah-48V-POE-Injector

R15,200.00

(R15,200.00 unit)

Tax included
Reference: FOS-SOL-K12AH

A off grid Pole mount Solar System to power a high site internet or communications gateway i.e. no additional equipment. This pole-mounted solar power kit with Lithium battery is designed to power a high site gateway, to power most 48v POE equipment . 2 x 30W solar panels, 2 x 12V 12Ah LiFeP04 + 48V POE Injector.

Read our FAQ on Solar here.

Please note this kit does NOT include a camera or the gateway

Last items in stock

  Delivery policy

All local packages are shipped via The Courier Guy with tracking and drop-off with signature.

Are you looking for a way to provide power and remote connectivity to your own IP camera or other device in an off grid area? Then Foscam CCTV has the solution.

Enclosure complete with:

24Ah LiFeP04 battery pack + BMS

Solar Charge Controller

Dedicated 12VDC Voltage protector for 2 x Cameras

Dedicated 5VDC USB connector

Unregulated (charging voltage) DC supply for CPE / gateway

48V Active POE injector

Power Connectors (5 x 2.2mm), glands, Solar Panel integrated mounting brackets

60W (2 x 30W) Solar panel complete with:

Integrated pole mount brackets, U-clamps for 50mm diameter pole

Foscam’s Off Grid Solar Security Hub provides a regulated 12v supply to power your device along with a standard USB outlet. This model will power one Foscam camera 24/7 with back-up battery with 60hr to 80hr run-time (Winter solstice).

Power system

The system has its own Lithium battery charged via an on board solar panel allowing it to run indefinitely with out refuelling or recharging from the mains. It’s completely silent with no noisy generators or hazardous fuel stored on site – perfect for residential areas or a long deployment. The power system is designed for SA conditions and is fully compliant with SA electrical regulations. It includes an industrial 12v regulated power supply to protect your equipment from voltage variances.

Recovery time from full discharge: less than 30mins at 50% solar power.

SPECIFICATIONS – Solar Mount

Pole mount housing

The entire system is housed in an industrial grade IP66 rated enclosure supported by a rugged pole mount frame. The standard enclosure is designed to connect to an external device (such as an IP camera).

Pole mount for solar panel: Aluminium alloy brackets with stainless steel hardware

Setting angle: 45° for capturing the correct angle for the sun

Mounting pole (to be supplied by installer/customer for combination of solar panels and battery/control box): recommended minimum - 75mm x 3mm steel for 3metre above ground

NOTE: POLE is NOT INCLUDED in the kit and dimension are only a guideline. It is the responsibility of the client to ensure that correct erection procedure for the pole is followed.

Wind load: 80Kkm/Hr

Hail loading: 1.1Kn/m ²

Assembled weight (includes 2 x 30W panel): 8kg

Attention: Edges may be sharp

Solar panel mount set comes with: 1 upper bracket, 1 lower bracket, 2 x U-bolts (straps), 2 x M6 hex-head bolts, 4 x washers, 2 x M6 nyloc nuts, 2 x M6 hex-head bolts for solar panel, 4 x flat washers for solar panel, 2 x nyloc nuts for solar panel.

Installation: To the greatest extent possible, the installation site should allow unshaded exposure to the sun throughout daylight hours.

This kit comes with 2 X 12Ah battery kits.

Solar charging is by means of a Monocrystalline Solar panel

The solid state controller integrates all aspects required for optimal operation of the unit with:

  • Solar charge controller specifically for LiFepo4 cells with BMS on 12Ah unit
  • Regulated outputs for two cameras and a USB communication device
  • Raw output for a 12V - CPE link

Cabinet: Polyester / Polycarb 300 x 250 x 130mm

Pole mount bracket: U-clamp / strap top and bottom

Batteries: 2 x 12V 12Ah LiFeP04 batt pack

Solar Charge Controller: 10A

Camera Voltage Protector: 2A

Contains:

Power Connectors for: Camera; Router; Solar panels

Total Weight of control and battery cabinet: 10kg

Cabinet mounting set comes with:

1 upper bracket, 1 lower bracket, 2 x U-bolts (straps),

4 x M6 hex-head bolts, 8 x washers, 4 x M6 nyloc nuts

We custom build to suit your project or device, let us know what you are looking for by email (sales@foscam.co.za) or call us on +27 11 465 9173 and we’ll provide you with a quote.

FOS-SOL-K12AH
1 Item

Specific References

New product

in the same category

Instagram